Troubleshooting · Oral solid dosage

Capping and Sticking in Tablets: Machine or Formulation?

By the Hello Pharma Editorial Team · Last updated 19 November 2026 · 3 min read

Short answer

Capping and lamination are mainly caused by air trapped in the compact, which expands after compression. On the machine side, fix it with more pre-compression, longer dwell time (slower turret or larger punch heads), less upper punch penetration, and well-maintained tooling. Sticking and picking are mainly moisture, lubrication and tooling-surface problems. If a defect follows the product across presses, it is mostly formulation; if it follows a press, a station or a tooling set, it is mostly machine.

Definitions

  • Capping: the top or bottom of the tablet separates, partly or fully.
  • Lamination: the tablet splits into horizontal layers.
  • Sticking: material sticks to punch faces.
  • Picking: material is pulled out of embossing or lettering (inside letters such as A, B and O).

Diagnostic tree

  1. Does the defect follow the product to another press? Yes: start with formulation. No: start with the machine.
  2. Is it limited to certain stations? Yes: inspect those punches and dies (wear, "claw" edges, length, surface).
  3. Does it get worse with speed? Yes: dwell time or air entrapment; slow down or increase pre-compression.
  4. Does it get worse over the run? Yes: tooling build-up, heat, or moisture pick-up from the room.
  5. Did it start with a new batch of granules? Yes: check moisture, fines and particle size distribution.

Machine causes and fixes

DefectMachine causeFix
Capping, laminationToo little pre-compressionIncrease pre-compression (too much can also fracture tablets)
Capping, laminationHigh turret speed, short dwellReduce speed; use tooling with larger head flats
CappingDeep upper punch penetrationMinimise upper punch penetration
CappingWorn tooling, concave edges forming a "claw"Refurbish or replace punches; check die wear rings
Capping, chippingSweep-off blade or take-off set wrongAdjust take-off and ejection
Sticking, pickingRough or worn punch faces; embossing designPolish or coat punches; revise embossing
StickingHumid room or heat build-upControl room humidity and temperature

Formulation causes and fixes

  • Capping: too many fines, granules too dry or too hard, poor bonding, bimodal particle size distribution; reduce fines, adjust moisture, revise binder.
  • Sticking: excessive moisture, too little lubricant, low-melting components; dry adequately, optimise lubricant level and blending time.
  • Once a formulation is approved, changes are limited, so production often relies on press settings. Catch defects early in development with a compaction simulator; see our R&D press guide.

Companies listed in the Hello Pharma supplier directory

The Hello Pharma supplier directory lists 111 companies relevant to this guide, grouped below by machine type or category. Each name links to the company's directory entry, with a description, technologies, location and website. Companies confirmed against their websites or public listings appear first in each group.

Inclusion is not an endorsement or ranking. Many categories are inferred from company names and segments, so confirm capabilities, approvals and service reach directly with each supplier. Search all 1,232 companies.

Punches and dies (10)

Concept Engineering; Fluidpack; Karnavati Engineering; Parle Global Technologies Pvt. Ltd.; Accura Pharmaquip Pvt Ltd; J.P. Machine Tools; Kothari Pharma Technologies Private Ltd.; Pacific Tools Pvt. Ltd; Pharma Spares Pvt. Ltd.; Sharad Micro Die & Engg. Works.

Open the full entries: Oral solid dosage equipment list filtered to punches and dies · Components and spares list filtered to punches and dies

Tablet presses (21)

ACG Worldwide Solid Dosage Consumables and Machinery; Cadmach Machinery Co. Pvt Ltd; Concept Engineering; Fluidpack; Karnavati Engineering; Parle Global Technologies Pvt. Ltd.; Prism Pharma Machinery; Solace Engineers (Mktg) Pvt. Ltd.; Accura Pharmaquip Pvt Ltd; Dumra Machines; Grovers International; Helios Concrew Machines; Imperial Pharmachines Pvt Ltd; Kothari Pharma Technologies Private Ltd.; Kunal Machines; LE - Born Technomech; NEO Machine Mfg Co LTD; Omega Pharma Machinery; Propix Technologies Pvt Ltd; Richards Industries; Saimach Pharmatech Pvt. Ltd..

Open the full entries: Oral solid dosage equipment list filtered to tablet presses

Excipients (86)

A&C PharmaSpecialities LLP; AAK India Pvt. Ltd.; Accent Microcell Limited; Actylis; Amano Enzyme Asia Pacific Co, Ltd; Ankit Pulps & Boards Pvt. Ltd.; ANSH Pharma Ingredients LLP; Asian Flavours & Fragrances (Bombay); BASF India Limited; Bharat Coats; Bloomage Biotechnology Corp, Ltd.; Clariant India Pvt Ltd; Coat & Coat Pharmacare; Colorcon Asia Pvt Ltd; Croda India Company Pvt Ltd; DB Ingredients; DFE Pharma India Private Limited; Doshion Polyscience Pvt. Ltd.; DuPont Specialty Products India Pvt Ltd; Elkay Chemicals Pvt. Ltd.; Ennature Biopharma- A Division of India Glycols Limited; Enrobage India Pvt Ltd; Esschem Pvt. Ltd.; Evonik India Pvt. Ltd.; Flavaroma Flavours and Fragrances; Gandhar Oil Refinery (India) Ltd; Gangotri Inorganic Private Limited; Gattefosse India Pvt. Ltd.; Grace Davison Chemicals (India) Pvt. Ltd.; Himachal Polyolefins Limited; Hindustan Phosphates Pvt Ltd; Hy-Gro Chemicals Pharmtek Pvt Ltd; Ideal Cures Pvt Ltd; India Phosphate & Allied Industries Pvt. Ltd.; Innophos Inc.; Iris Ingredients; JRS Pharma ( Rettenmaier India Pvt Ltd); K. P. Manish Global Ingredients Pvt Ltd; Kalyani Mine Products Private Limited; KK India Petroleum Specialties Pvt Ltd. and 46 more.

Open the full entries: Excipients and ingredients list filtered to excipients

Frequently asked questions

What is the main cause of tablet capping?

Air trapped in the powder during compression, which expands when pressure is released and splits the tablet. Fast speeds, low pre-compression, worn tooling and too many fines make it worse.

Does slowing the press stop capping?

Often, because longer dwell time lets air escape and particles bond. Increasing pre-compression is another first step.

How do I tell if sticking is caused by the machine or the blend?

If sticking appears on certain punches or after long runs, look at tooling surfaces and heat. If it appears with a new batch or in humid conditions, look at moisture and lubrication.

Can punch coatings prevent sticking?

Coatings such as chrome or specialised surface treatments can reduce sticking for some products, alongside polishing and correct embossing design.

Related guides

Sources

  1. Press adjustments help prevent tableting problems, Pharmaceutical Technology
  2. Fixing tableting problems, Pharmaceutical Technology
  3. Process and formulation considerations to avoid tablet defects, Scientist Live
  4. Troubleshooting tablet defects in no time, Medelpharm
  5. Common tablet compression issues, Jinlu Packing

This guide is general information to support decisions and is not engineering, validation or regulatory advice for a specific project.

Ready to read pharma differently?

Join the Hello Pharma community for editorial, intelligence and engineering reference from pharma manufacturing.