Comparison · Packaging and serialization

Alu-Alu vs PVC Blister Machines: Cost, Speed and Product Fit

By the Hello Pharma Editorial Team · Last updated 19 November 2026 · 3 min read

Short answer

Choose alu-alu (cold-form) blisters when a product is sensitive to moisture, oxygen or light, or is sold into hot, humid climates, because the aluminium laminate gives a near-total barrier. Choose PVC or PVC/PVDC thermoformed blisters for everything else: they cost less per pack, run faster, give smaller packs and let patients see the tablet. Industry estimates put alu-alu packs at roughly 25 to 50 percent more per pack than PVC-based blisters.

How the two blister types are made

Thermoform (PVC, PVC/PVDC, PVC/Aclar): a plastic film is heated and formed into pockets with air pressure or plugs, filled with tablets or capsules, and sealed with aluminium lidding foil. The plastic can be plain PVC or coated or laminated with PVDC or PCTFE (Aclar) to improve the moisture barrier.

Cold form (alu-alu): a laminate of oriented polyamide, aluminium foil and PVC is pressed into pockets cold, by mechanical plugs, then filled and sealed with aluminium lidding. Because the product is enclosed in aluminium on both sides, the barrier is near total. Cold-forming needs different tooling, and many modern blister machines can run both formats with a tooling change.

Barrier performance

The barrier of a blister comes from both the cavity material and the sealed seam. In thermoformed blisters, almost all moisture enters through the cavity; in alu-alu blisters, the cavity is effectively closed and the small remaining ingress comes through the sealed seam. One published calculation of water vapour transmission per blister (38 °C, 90% relative humidity) illustrates the gap:

Forming materialMoisture ingress relative to alu-alu
250 µm PVC with 40 gsm PVDCabout 62×
250 µm PVC with 60 gsm PVDCabout 47×
15 µm Aclar on 200 µm PVCabout 31×
51 µm Aclar on 200 µm PVCabout 12×
Alu-alu (oPA / Al / PVC)1× (reference)
Calculated values from a lidding foil supplier's technical comparison. Actual performance depends on film grade, cavity size, seal quality and storage conditions.

Plain PVC, without a coating, has a much weaker moisture barrier than any of these and suits only products that are not moisture-sensitive.

Cost, speed and pack size

FactorPVC / PVDC thermoformAlu-alu cold form
Material cost per packLowerHigher; estimates of roughly 25 to 50 percent more per pack
Machine speedFasterSlower; cold-forming and larger cavities reduce output
Pack sizeCompact, deep pockets possibleLarger cards: cold-formed pockets need gentler walls and more spacing
Product visibilityClear, product visibleOpaque
InspectionCamera inspection through the filmProduct must be inspected before sealing
ToolingHeated forming toolsCold-forming plugs and dies

Decision table

SituationUsual choice
Hygroscopic or moisture-sensitive product, or stability fails in PVC/PVDCAlu-alu
Light-sensitive productAlu-alu, or an opaque or tinted thermoform film if stability allows
Export to hot, humid climate zones (ICH zones IVa and IVb)Alu-alu or a high-barrier PVC/Aclar, confirmed by stability data
Stable product, high volume, cost-sensitive marketPVC/PVDC
Patient needs to see the product, or brand recognition by appearanceThermoform
Barrier needed but alu-alu card size is a problemPVC/Aclar thermoform

The deciding evidence is always the product's stability data in the chosen pack under the climate zone conditions of the target markets.

Buying the machine: what to check

  • Can the machine run both thermoform and cold-form formats, and how long does a format change take?
  • What is the rated output in blisters per minute for your card size in each format, not just the maximum speed?
  • How is the product inspected before sealing on alu-alu runs?
  • Which sealing method (flat platen or rotary) does it use, and how is seal integrity checked?
  • Can the line feed directly into a cartoner, and is serialization of the carton supported downstream?

Companies listed in the Hello Pharma supplier directory

The Hello Pharma supplier directory lists 21 companies relevant to this guide, grouped below by machine type or category. Each name links to the company's directory entry, with a description, technologies, location and website. Companies confirmed against their websites or public listings appear first in each group.

Inclusion is not an endorsement or ranking. Many categories are inferred from company names and segments, so confirm capabilities, approvals and service reach directly with each supplier. Search all 1,232 companies.

Blister packing (13)

Accupack Engineering Pvt Ltd; Accurate Machines; ACG Worldwide Solid Dosage Consumables and Machinery; Autopack Industries; Bliss-ca Technologies; Elmach Packages (India) Pvt Ltd; Parle Global Technologies Pvt. Ltd.; Salesworth Synergies LLP; Anchor Mark Pvt Ltd; Doctor Pack India Pvt. Ltd.; Groynetech; Sriven Autopac Pvt. Ltd.; Vandana Electronics (Pharma Packaging Solutions).

Open the full entries: Packaging machinery list filtered to blister packing · Oral solid dosage equipment list filtered to blister packing · Distribution, trade and services list filtered to blister packing

Foils and films (9)

ACG Worldwide Solid Dosage Consumables and Machinery; Amcor Flexibles India Private Ltd; Jagson Engineers; R. S Foils Pvt Ltd; Raviraj Foils Ltd; Skypack India Pvt Ltd; Svam Packaging Industries; Uflex Limited; Ultra Foil.

Open the full entries: Packaging materials list filtered to foils and films · Packaging machinery list filtered to foils and films · Oral solid dosage equipment list filtered to foils and films

Frequently asked questions

Is alu-alu blister packaging always better?

It gives the best barrier, but it costs more per pack, runs slower, makes larger packs and hides the product. For stable products, PVC or PVC/PVDC is usually the better choice. The product's stability data should decide.

Can the same blister machine run alu-alu and PVC?

Many modern blister machines can run both, using cold-forming tooling for alu-alu and heated forming for thermoform. Check the changeover time and output in each format.

What is PVDC coating?

PVDC (polyvinylidene chloride) is a coating applied to PVC film that greatly improves its moisture and oxygen barrier while keeping the pack clear. It is measured in grams per square metre; heavier coatings give a better barrier.

Why are alu-alu blisters larger?

Aluminium laminate cannot be stretched as far as heated plastic, so cold-formed pockets need wider, gentler walls and more space between pockets, which makes the card larger for the same number of tablets.

Related guides

Sources

  1. Comparison of permeability, alu-alu vs barrier films, lidding foil technical paper
  2. What is alu-alu blister packaging (cost estimates), JL Packing
  3. Alu-alu vs alu-PVC selection guide, JL Packing
  4. High-barrier materials: Aclar, PVDC and alu-alu, Racklify
  5. Pharmaceutically compliant blister machines, Uhlmann

This guide is general information to support decisions and is not engineering, validation or regulatory advice for a specific project.

Ready to read pharma differently?

Join the Hello Pharma community for editorial, intelligence and engineering reference from pharma manufacturing.