Guide · Sterile and injectables

Manufacturing Vessels and CIP/SIP Systems for Injectables

By the Hello Pharma Editorial Team · Last updated 19 November 2026 · 3 min read

Short answer

Injectable compounding vessels are jacketed 316L stainless steel tanks with sanitary fittings, polished, drainable product surfaces (commonly Ra 0.4 to 0.5 µm or better, often electropolished), magnetic or sealed mixers, sterile vent filters and spray devices. Clean-in-place (CIP) washes vessels and lines with detergents and WFI rinses without dismantling; sterilisation-in-place (SIP) uses pure steam, typically at 121 °C or higher, to sterilise vessels, filter housings and transfer lines. Single-use bags are a strong alternative for multi-product and biologics plants.

Vessel design essentials

FeatureTypical specification
Material316L stainless steel product contact; certified material
Surface finishMechanically polished and often electropolished; Ra commonly 0.4 to 0.5 µm or better
DrainabilitySloped dished bottoms and lines; bottom-mounted drain valve
Dead legsMinimised per ASME BPE guidance
MixerBottom-mounted magnetic mixer or sealed top-entry agitator
JacketHeating and cooling for formulation and SIP cool-down
InstrumentationLoad cells or level, temperature, pressure; sanitary sensors
VentSterilising grade, heated or steam-traced vent filter
RatingPressure and vacuum rated for SIP

CIP cycle

  1. Pre-rinse with purified water or WFI.
  2. Caustic wash (hot), often with detergent.
  3. Intermediate rinse.
  4. Acid wash where needed for mineral or protein residues.
  5. Final WFI rinse, checked by conductivity and sometimes TOC.
  6. Air blow or drying.

Spray balls or rotating spray devices must cover all surfaces, confirmed by riboflavin coverage tests, and cleaning is validated against residue limits.

SIP cycle

  • Pure steam enters at high points; condensate and air are removed at low points through steam traps.
  • Exposure at typically 121 °C or higher for a validated time, confirmed by temperature probes at cold spots and biological indicators.
  • Cool-down under sterile air or nitrogen overpressure to avoid drawing in non-sterile air.
  • Filter housings and transfer lines are sterilised with the vessel.

Stainless steel or single-use?

FactorStainless steel with CIP/SIPSingle-use bags and assemblies
Capital costHigher; utilities for WFI and pure steamLower capital, higher consumable cost
ChangeoverCleaning validation, long turnaroundFast; no cleaning
Batch sizeLarge volumesUp to a few thousand litres
RisksCleaning residues, cross-contaminationExtractables and leachables, supply continuity

Utility needs are covered in WFI and pure steam systems.

Companies listed in the Hello Pharma supplier directory

The Hello Pharma supplier directory lists 52 companies relevant to this guide, grouped below by machine type or category. Each name links to the company's directory entry, with a description, technologies, location and website. Companies confirmed against their websites or public listings appear first in each group.

Inclusion is not an endorsement or ranking. Many categories are inferred from company names and segments, so confirm capabilities, approvals and service reach directly with each supplier. Search all 1,232 companies.

Reactors and vessels (16)

Adam Fabriwerk; D.D. Enterprises; GMM Pfaudler Ltd.; Praj HiPurity Systems Limited.; Propack Technologies Pvt Ltd; S.K. Pharma Machinery Pvt Ltd; Shiv Shakti Process Equipment Pvt. Ltd.; Standard Group of Companies, Hyderabad; Amar Equipments Pvt Ltd; Chemi Plant Engineering Company; Hugopharm Technologies Private Limited; Linyi Haixin Chemical Equipment Co, Ltd; Pharma Chem Machineries; SA Tournaire; Sheth Fabricators Pvt. Ltd.; Vats & Vessels (I) Pvt Ltd.

Open the full entries: Process plant equipment list filtered to reactors and vessels · Sterile, injectable and liquid equipment list filtered to reactors and vessels · Water and utilities list filtered to reactors and vessels · Lab and analytical list filtered to reactors and vessels

SS fabrication (26)

Swiss Engineering Pvt Ltd; Allyone Industries; Chemi Plant Engineering Company; Cintex Industrial Corporation; Darshana Industries Pvt. Ltd.; G T Metals & Tubes; HLE Engineers Pvt. Ltd.; Hugopharm Technologies Private Limited; Kaps Engineers; Kinam Engineering Industries; Komal Industries; Mistry Engineering; N. K. Industries; Neptune Industries; Pharma Fab Industries; Shah Brothers; Shefa Industries; Sheth Fabricators Pvt. Ltd.; Sterinox Systems; Taskar Engineering; Tex Mech Engineers; Trimech Engineers Pvt. Ltd.; Universal Orbital Systems Pvt. Ltd.; Vats & Vessels (I) Pvt Ltd; Vishwakarma Industries; Vyanktesh Fabricraft Pvt. Ltd..

Open the full entries: Process plant equipment list filtered to ss fabrication · Oral solid dosage equipment list filtered to ss fabrication

Pumps and valves (15)

IDEX Fluid & Metering Pvt. Ltd.; Sanbij Impex Pvt Ltd; Swiss Engineering Pvt Ltd; Apurva India Pvt. Ltd.; Busch Vacuum India Pvt Ltd; Cipriani Harrison Valves Pvt Ltd; Condot System Pvt Ltd; DHV Fiting Pvt. Ltd.; Flocon Industries; Fristam Pumps India Pvt. Ltd.; Mascon Techneeds; Piab Vacuum Technology Pvt. Ltd.; RGS Vacuum Solutions Pvt. Ltd.; Tecnik Fluid Controls Pvt Ltd; Valfit Engineers.

Open the full entries: Process plant equipment list filtered to pumps and valves

Frequently asked questions

What surface finish is used for injectable vessels?

Polished 316L stainless steel, commonly Ra 0.4 to 0.5 µm or better, and often electropolished, following ASME BPE practice.

What is the difference between CIP and SIP?

CIP cleans equipment in place with detergents and rinses; SIP then sterilises it in place, usually with pure steam.

At what temperature is SIP performed?

Typically 121 °C or higher, for a validated exposure time at the coldest points.

When should single-use systems be used?

For multi-product, biologics and smaller batches where fast changeover and avoiding cleaning validation outweigh consumable costs.

Related guides

Sources

  1. Qualification and validation of depyrogenation tunnels and autoclaves (SIP context), Pharmaceutical Online
  2. Revised WFI guidelines and ISPE water and steam guide, Manufacturing Chemist
  3. Peristaltic aseptic filling and single-use tubing sets, Pumps and Systems
  4. EU GMP Annex 1 overview, NSF

This guide is general information to support decisions and is not engineering, validation or regulatory advice for a specific project.

Ready to read pharma differently?

Join the Hello Pharma community for editorial, intelligence and engineering reference from pharma manufacturing.